Linear Technologies Manuals. RCA Manuals. Dallas Semiconductor Manuals. Harris Manuals. Rectifiers scrs Triacs Manuals. Maxim Manuals. Philips Manuals. IC Datasheet: Radiotron Designers Handbook Topics: voltage, frequency, grid, circuit, plate, output, input, resistance, valve, current, plate current, Scenix Manuals.
SGS Manuals. Intersil Manuals. IC Datasheet: Sharp Microcomputer Data Book Topics: output, interrupt, clock, input, timer, pin, sharp, mode, data, control register, system clock, IC Datasheet: Mostek Topics: data, output, input, address, figure, interrupt, pin, cycle, clock, min max, power supply, hold This manual comes under the category Drill Machines and has been rated by 1 people with an average of a 8.
This manual is available in the following languages: English. Is your question not listed? This manual contains important information about product safety.
Please read. Please keep this. Check the rotational direction. The bit rotates clockwise viewed from the rear side by pushing the R-side of the selector button. The L-side of the selector button is pushed to turn the bit counterclockwise See Fig.
The L and R marks are provided on the selector button. When the trigger switch is depressed, the tool rotates. When the trigger is released, the tool stops.
The rotational speed of the drill can be controlled by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more. A buzzing noise is produced when the motor is about to rotate. This is only a noise, not a machine failure. Excessive pressing force never increases drilling speed. It will not only damage the drill tip or reduce working efficiency, but could also shorten the service life of drill bit.
Operate the hammer drill within kg pressing force while drilling into brick. If the sharp bit such as drill is fitted to the power tool when carrying it with hooked to your waist belt, you will be injured. Unless the hook is securely installed, it may cause an injury while using.
Install securely the hook in the groove of power tool and tighten the screws to fix the hook firmly. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Norcross, GA Export Blvd. NOTE emphasizes essential information.
Cluttered or dark areas invite accidents. Power tools create sparks which may ignite the dust or fumes. Distractions can cause you to lose control. Do not use any adapter plugs with earthed grounded power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock. Water entering a power tool will increase the risk of electric shock. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. Use of a cord suitable for outdoor use reduces the risk of electric shock. This enables better control of the power tool in unexpected situations.
Loose clothes, jewellery or long hair can be caught in moving parts. Use of these devices can reduce dust-related hazards. Power tools are dangerous in the hands of untrained users. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. Use of any other battery packs may create a risk of injury and fire. Shorting the battery terminals together may cause burns or a fire. This will ensure that the safety of the power tool is maintained.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
Exposure to noise can cause hearing loss. NEVER touch moving parts. Use right tool. Handle tool correctly. Before using battery charger, read all instructions and cautionary markings on 1 battery charger, 2 battery, and 3 product using battery.
Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. If extension cord must be used make sure: a. That blades of extension cord are the same number, size, and shape as those of plug on battery charger: b.
That extension cord is properly wired and in good electrical condition; and c. English 1. In such case, charge it up immediately. WARNING In order to prevent any battery leakage, heat generation, smoke emission, explosion and ignition beforehand, please be sure to heed the following precautions. During work make sure that swarf and dust do not fall on the battery. Do not store an unused battery in a location exposed to swarf and dust. If left untreated, the liquid may cause eyeproblems.
WARNING If an electrically conductive foreign object enters the terminals of the lithium ion battery, a short-circuit may occur resulting in the risk of fire. English Do not place electrically conductive cuttings, nails, steel wire, copper wire or other wire in the storage case.
Driving and removing of machine screws, screws, tapping screws, etc. Battery removal Hold the handle tightly and push the battery latch to remove the battery See Fig. Battery installation Insert the battery while observing its polarities See Fig. The power source voltage is stated on the nameplate.
The cord is not damaged. Have it repaired immediately. Charging When the battery is connected to the battery charger, charging will commence and the pilot lamp will light in red. See Table 2 NOTE: If the pilot lamp flikers in red, pull out the plug from the receptacle and check if the battery is properly mounted.
At 1-second intervals See Table 2 1 Pilot lamp indication The indications of the pilot lamp will be as shown in Table 2, according to the condition of the charger or the rechargeable battery. Does not light charging for 0. Does not light red complete for 0. Does not light Battery overheated. Charging will commence when battery cools. NOTE: The charging time may vary according to temperature and power source voltage. B b in the direction of the arrow. B in a direction other than that of the arrow could damage the connector.
Page Power Cable, Smps P. B Power Cable a 1 Disconnect the connector of the power cable. SMPS P. B b 3 Disconnect the two connectors. B c in the direction of the arrow. Page Hdmi Block, Hdmi P. B 1 Disconnect the FFC. B and the HDMI frame c. Page Hdd Block, Hdd P. HDD P. Page Card P. B a in the direction of the arrow. B 2 [C] Unlock B in the direction of the arrow. B [Component replacement] PIN NO.
0コメント